Our 33 Litre Front Loading Benchtop Autoclave, available in Classic and Autofill versions, is ideal for laboratory research and is low in water. Have a question about Autoclaves, Sterilizers or Steam Generators? Our FAQ page has the answers. All the machines are supplied with a user manual but sometimes it is not consulted! Astell offer training to operators, and this is a service I recommend to ensure.
|Published (Last):||20 April 2012|
|PDF File Size:||3.25 Mb|
|ePub File Size:||16.47 Mb|
|Price:||Free* [*Free Regsitration Required]|
Allows an Astell Service Manaul remote access to the unit’s touchscreen controller, e. The 33 to 63 litre front loading ‘Benchtop’ autoclaves are available in two versions.
A supply of compressed air is essential on all units with vacuum fitted. Most user actions amnual Yes – No or similar answers to questions shown on the display, and those that require more complicated entries explain the data as it astelo presented and provide confirmation of the results. Please contact Astell for further details. Advanced Water Cooling offers substantial sterilization cycle time savings and is ideal for the busy Laboratory.
Directives and will void the CE mark. Please ensure that the paper loading method described here is used. Where a load is suitable for the inclusion of a sensor, and the thermal mass is high compared to the surface area, then Load Sensing can be used to advantage.
A astel, of,and litres models Fully programmable 5. Separate Astell Scientific Manuals are supplied when a Chart Recorder option is specified giving details of recorder operation and specifications. These will wipe any settings previously entered by the asteell. The existing Title is shown on the top line, and each Character of the title is selected in turn and shown in the bottom right – hand corner of the display.
These readouts are only displayed when necessary in the cycle. Not all will show on all models.
Litre Front Loading Autoclave | Astell UK
However we will also try to troubleshoot and offer advice to minimise any potential disruption. Customers also need to ensure the water they use is of the required quality; hard water can cause scale problems which will reduce the life of the heaters — so a water softener is recommended in such cases.
Unit includes a separate brine tank, allowing installation in difficult or restricted positions. You will be asked to confirm. It must be set to an asteell temperature that will operate safely for all autpclave and loads. All device changes and signatures are electronically logged and saved in a file format that cannot be altered in any way.
It autoclaave intended to be used only by qualified engineers who have been shown how to perform such adjustments by the manufacturer’s agent, or who are carrying out such adjustments on behalf of or under the instruction of the manufacturer.
This achieves a threshold temperature exactly the same as the Sterilizing temperature and a further function compensates for the small temperature offset between load and chamber during Sterilizing experienced in normal use. The printer can also be used to provide reports of cycle settings and servicing information. Requires a mains water supply. When the load reaches 1. The media will be kept warm for up to 48 Hrs. Continued use of a machine which does not comply is a criminal offence under E.
Smaller capacity autoclaves, including most circular section machines require servicing once or twice a year depending on regularity of use. During this period the Timing functions continue to run and the Temperature Control system will operate as normally but TIMES will not be visible to the operator until the Calibrate Mode has been left. A choice of 33, 43 and 63 litre models Self contained design with no installation required – just fill it with water and plug it in and the machine is ready to be used No mains water supply or drain necessary Fully programmable 5.
Air Ballast reduces the risk of bottled fluids boiling over when an efficient cooling system e. If ON only the supervisor may select Programs, via the Key button. Do NOT pull the paper vertically out of the printer!!! It’s a community-based project which helps to repair anything. If pressing the key does not have the desired effectkeep pressing for up to 2 seconds. The ‘Swiftlock’ front loading range of autoclaves allows the user a greater choice of options unavailable on the smaller ranges, as well as easy loading access.
Models without printer reset to Is it possible to keep media warm using Holdwarm whilst removing bottles from time to time?
33 Litre Front Loading Benchtop Autoclave | Astell UK
Astell can custom build the Benchtop range to your specifications. Note;- This requires the printer option to be fitted. Programming and Controller Operation are covered in depth but this manual does not cover day-to-day operation of the Autoclave itselfLoading or Sterilizing advice.
In combination with the jacket option, a drying stage then begins to ensure loads are touch dry upon removal. Use only if you are totally sure that you wish to reset program settings.
The Astell 33 – 63 Litre Benchtop Autoclave Range
The ENGINEER will normally need to have been trained in astelp relevant disciplinepossibly as a Sterilizing Engineerbe conversant with Micro-Electronic system handling procedures, and be suitably qualified to carry out the adjustments and changes that may be required. Our service staff are able to repair or maintain your equipment on site if required.
Consult Factory for details. Astell Scientific offer servicing contract options for all the sterilization equipment we manufacture. Set up the Sterilizer with no load, and close the cover. Fit the roller into the clips. Can Petri dishes with manuxl be sterilised in an open discard bag in autoclaves 63 litres and under?