ASTM F1929-98 PDF

ASTM F1929-98 PDF

The current test method is ASTM F dye penetration. . ASTM F – 98 ( Reapproved ) Standard Test Method for Detecting Seal. Leaks in Porous. 1 This test method is under the jurisdiction of ASTM Committee F02 on Flexible Last previous edition approved in as F – ASTM F testing defines materials and a procedure that will detect and locate a leak equal or greater than a channel formed by a 50 μm ( in.) wire in.

Author: Gardashakar Kam
Country: Greece
Language: English (Spanish)
Genre: Software
Published (Last): 5 October 2006
Pages: 200
PDF File Size: 10.80 Mb
ePub File Size: 11.76 Mb
ISBN: 847-7-78805-768-3
Downloads: 61992
Price: Free* [*Free Regsitration Required]
Uploader: Fetaur

Please contact us with any questions you may have about ASTM F, or if we can help you with any other testing questions or projects. This pressure creates the force needed to rupture the seal. These leaks are frequently discovered at seals between package components of the same or dissimilar materials. Learn more about the different testing services provided at each location.

Because air escapes through the walls of a porous package during inflation, the flow rate must be increased to compensate for the lost air through the walls and create the back pressure in the porous package.

ASTM-F – Medical Package Testing

Leaks may also result from a microscopic pinhole in the packaging material that is invisible to the human eye. However, since ASTM F testing is designed solely axtm detect leakage, components that illustrate any indication of leakage are usually rejected.

  ASTM D6926 PDF

Here is a quick overview astmm the changes: Requirements Satm F testing is limited to porous materials which can retain the dye penetrant solution and prevent it from discoloring the entire seal for a minimum of 20 seconds.

The package will be visually inspected for dye penetration after contact with the dye penetrant for a specified time. Place a bead of solution between the two materials along the outer edge of the package seal, ensuring the entire outer edge of the seal is wetted with the dye solution.

The Creep Test provides a test for slow shear of the adhesive bond similar to a dead aztm hanging on the seal. As a guide, each Test Method above recommends observing each seal for a maximum of 5 seconds on a 4-sided package 20 seconds total.

If ASTM F testing is used as the quality control method, the test specimen must consist of a complete packaged device.

Harmful biological or particulate contaminants may enter the device through leaks. In the Burst Testair is introduced into the package at a predetermined pressure and flow rate.

Packaging must be free of condensation or any other source of liquid water. There is no general consensus f19229-98 the level of leakage that is likely to be detrimental to a particular package.

Overview of ASTM F Dye Penetration Integrity Test

The dye will have discolored aatm surface of the material. The dye solution used in penetration testing will wick through any porous material over time, but normally not within the suggested maximum time.

  DUA E MUJEER WITH URDU TRANSLATION PDF

Along the extended unsealed area beyond outer seal edgethe transparent material is separated from the porous material with use of a finger, paperclip, etc.

Observe each seal for a recommended duration of 5 to 20 seconds. Please keep this in mind when developing your studies and validations. If wicking does transpire, it may be verified by observing the porous side of the subject seal area.

Most commonly, an eyedropper or pipette is used to apply the dye penetration solution between the transparent and porous materials of the unsealed area. The Eyedropper method requires the packages to have an unsealed area that extends beyond the outer edge of the seal. For more information visit www. ASTM F procedure requires that the dye penetrant have good contrast to the opaque packaging material.

Overview of ASTM F1929 Dye Penetration Integrity Test

The porosity or lack thereof of the package material determines the inflation rate for the burst test. Observe the package for any leaks originating from the inside edge of the package seal towards the outside edge of the package seal. Water already in the seal defects may render them undetectable with a dye penetrant.

A dye penetrant solution is applied locally to the seal edge to be tested for leaks.