AS NZS 2693 PDF

AS NZS 2693 PDF

Specifies requirements for the design, construction, performance and labelling of jacks designed to raise vehicles. RECONFIRMATION NOTICE. Visit our website and learn more about AS/NZS REC standards. AS/NZS is a voluntary standard, except for those sections specifically called up by the consumer protection notice. It is important to note that the sections of.

Author: Tukus Arashijinn
Country: Equatorial Guinea
Language: English (Spanish)
Genre: Love
Published (Last): 6 January 2011
Pages: 495
PDF File Size: 14.14 Mb
ePub File Size: 14.52 Mb
ISBN: 772-8-19532-680-4
Downloads: 55232
Price: Free* [*Free Regsitration Required]
Uploader: Samurisar

The requirements or recommendations contained in published Standards are a consensus of the views of representative interests and also take account of comments received from other sources.

The handle provided for operation of the jack should, at the area where the operator applies the operating force, be of a size and shape which does not cause undue discomfort. A specific vehicle jack is only intended for changing wheels. This height represents the lowest position in the lifting cycle for all subsequent rig testing specified in this Paragraph C4. Use this form to make a general enquiry. Magna Carta— Tutohinga Nui Kore rawa e hoko ki te tangata, e kore e whakakdihoretia, e tautuku ranei te tangata ki te ture, tika ranei.

A new jack may be used for each test if required. During these tests it is desirable to have chocks placed near the wheels but not in contact with themor to provide some other means of preventing excessive movement of the vehicle in the event of a jack failing the tests. In FebruaryStandards Australia published a new standard for vehicle jacks. Alternatively, both organizations publish an annual printed Catalogue with full details of all current Standards. Returns are subject to customer following Beaver Brands’ recommended care and maintenance instructions which can be found on the garments swing tag.

ACCC accepts vehicle jacks undertaking 10 April Do not exceed the operating force specified in Clause 6. This is the initial operating force. Low Stock – Call To Order.

Jax Black Series 20 Tonnes AS/NZS

The mandatory standard is based on the and vehicle jacks standards which are published by Standards Australia. Suppliers of vehicle jacks should take cognizance of the regulations under the Trade Practices Act relating to the supply of these products. The jack shall be prepared for use in the normal manner, in accordance with the manufacturer’s instructions.

  D.C.HARRIS QUANTITATIVE CHEMICAL ANALYSIS PDF

The sa requirements include those relating to ease of use. Returns will be accepted for faulty or defective goods and any other non-excludable obligations of Beaver Brands set out in the Trade Practices Act or similar State and Territory legislation.

No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher. If the jack requires lubrication during the test it shall be in accordance with any lubrication requirements contained in the manufacturer’s instructions. Hydraulic jacks ws be supplied with hydraulic cylinders filled to the correct level with the recommended hydraulic fluid.

This Standard was issued in draft form for comment as DR The Standards Council of New Zealand is the national authority responsible for the production of Standards.

Terms Privacy Policy Sitemap Newsletter. Lifting cycles shall be carried out at a rate which corresponds to actual use and repeated at intervals which are sufficiently long to prevent overheating. The impulsive force at the lower end of the swing shall be applied to the head cap either directly, where applicable, or via a friction-free steel pushrod where the jack is not readily accessible see Figure Bl.

All bearings and moving parts requiring periodic lubrication shall be provided with readily accessible means of lubrication.

The ACCC’s website includes a full list of the mandatory product safety standards which can be accessed by visiting the For businesses page. Between editions, amendments may be issued.

The following are represented on Committee CS High lift jacks need not comply with this requirement. This includes any mass imposed on the towing vehicle when the combination vehicle is resting on a horizontal supporting plane.

If the jack is not az in a fully lubricated condition, it shall be provided with adequate instructions for initial lubrication. The ACCC was also concerned the jack represented it complied with the standard when this may not have been the case. Beaver Brands garments found to be faulty will be replaced at no cost.

  INTERIOR DESIGN WITH FENG SHUI BY SARAH ROSSBACH PDF

They reflect the latest scientific and industry experience. For rig testing, lower the head cap to the height specified in Step a.

Home Media Media releases. The ACCC was concerned Jayco’s failure to state the jack’s ‘safe working load’ or ‘working load limit’ as required by the mandatory standard posed a potential serious safety risk.

Visit our Web sites www. Skip to Content Skip to Sitemap.

Available for Delivery in 3 to 6 Days. The force shall be sustained for at least 30 s. Please address your comments to 26693 Chief Executive of either Standards Australia or Standards New Zealand at the address aa on the back cover. The force is measured at the centre of the handgrip or, if there is no handgrip, at a point 50 mm from the operator’s end of the handle.

Available on Back Order for Delivery.

Standards Catalogue

Note whether any overtravel occurs. Tests shall be carried out on a substantially level concrete surface or its zs. These vehicle jacks, which Jayco obtained from an Australian jack manufacturer, were not marked with their ‘safe working load’ or ‘working load limit’ as required by the prescribed mandatory consumer product safety standard under the Nzx Practices Act A ‘normative’ appendix is an integral part of a Standard.

To maintain their currency, all Standards are periodically reviewed, and new editions are published.

Where a means other than a dead weight is employed, the actual force applied 2639 the head cap shall be continuously measured and recorded during the first and th lifting cycles to ensure that the force is within the specified tolerances.

Special emergency tyres shall not be used when assessing compliance with this requirement.