INTECONT TERSUS MANUAL PDF

INTECONT TERSUS MANUAL PDF

Intecont Tersus – Free download as PDF File .pdf), Text File .txt) or read for weighing tasks better than % Manual and/or automatic zero setting Full. The INTECONT Tersus weighing elec- tronics is specially tion module, INTECONT Tersus optimally fits into any Manual and/or automatic zero setting. processes, the INTECONT Tersus meas- uring, control, and supervisory module, INTECONT Tersus optimally fits into any Manual and automatic zero setting.

Author: Gugrel Tygora
Country: Barbados
Language: English (Spanish)
Genre: Video
Published (Last): 25 April 2007
Pages: 331
PDF File Size: 18.22 Mb
ePub File Size: 19.57 Mb
ISBN: 719-7-78176-652-2
Downloads: 35124
Price: Free* [*Free Regsitration Required]
Uploader: Nehn

During office hours, service specialists from itecont divisions are on hand to analyze problems and failures. VeVeVeVertical to the belt conveyorrtical to the belt conveyorrtical to the belt conveyorrtical to the belt conveyor 0 must be entered as angle a. The result is compared to a predetermined reference value and then displayed. The belt speed is normally constant.

Are you looking for individual, perfect-fit service solu-tions? Tersuus covers the en-tire service spectrum, from simple inspections through to full service. The measuring system can be part of a more complex plant. Call up the function Setup – Service Values a tachometer The output frequency of the tachometer generator has to be less than 3, Hz when the measurement is manuap.

Change back to the first level. If Feedrate Setpoint P This changes the speed of intecony conveyor belt until the actual value is equal to the setpoint. The weighting of an impulse is defined by P They adapt their font size over 3 levels. Calibration Calibration of the pick-up input is not necessary. At right angles to the belt conveyor At right angles to the belt conveyor At right angles to the belt conveyor At right angles to the belt conveyor The angle a must be entered as the parameters.

  DSC LC-102PIGBSS PDF

The measuring rolls are linked with tdrsus frame construction via parallel plate springs. Display warning 2 Fig. Fading out may result in breaks in the numbering. It can be integrated in the control panel or is available with a glass fibre reinforced plastic wall-mounted housing for on-site installation. Stand-By W2 07 – Filters Number: Interrupt entry, continue with previous setpoint Delete symbols incorrectly keyed in Starting and interrupting Start the batch and the conveying process begins Interrupting a batch The batch is continued with the next start command.

The control or readjustment can take place using two different me-thods. The maximum permitted zero setting correction is monitored.

The Ethernet network connection is included in the basic equipment. Memory A P Key in the sensor width in P Operation remains in batch mode The next start command will begin a new batch; the previous batch will not be resumed.

Using weighing modules with leaf spring parallel guidance, lever ratio is always 1. Analyze any event messages that may appear and rectify the fault. The current value of the P This space has a yellow background. Subject to change without prior notice. Pulses per length P Usually, the time chosen is the time required for one belt circuit. Take appropriate action to ensure that the measuring sys-tem cannot be inadvertently restarted.

  CONVOCATORIA PRONABES OAXACA 2011 PDF

Bulk solids can be transported and cover the following equipment. The result is the feed rate I, from which the flow rate is determined.

Manual Intecont Tersus

The external clearance signal has to be pending selectableP Out of Tolerance W1 P If the optional activation is required on devices which have already been delivered, the data is transferred to the Schenck process, and the generated activation code is reported back. The counter protocol is available at any time.

Before performing work on the electrical equipment, disconnect the power supply. Call up the function block The previously selected function will be displayed if no event is pending.

Manual Intecont Tersus

Measurement is relocated to the material dispatch point using a special velocity-dependent delay element. PersonnelPersonnelPersonnelPersonnel Preparation, assembly, commissioning, operation, maintenance and servicing may only be carried out by qualified personnel.

The zero setting records the zero point fault on an empty belt over one or several whole-number belt circuits. Function block Calibration CW: Parameters are composed as follows: This would change the timing of calibration programs. The feed rate is regulated on a weighfeeder according to a setpoint. This increases the scale’s short-term accuracy.